- 1 How do you light a gas heater in a house?
- 2 Why is my gas heater not turning on?
- 3 Are indoor gas heaters safe?
- 4 What do you do when your gas heater stops working?
- 5 How does a heater work in a house?
- 6 Why is my heat not kicking on?
- 7 Should the pilot light always be on in a gas heater?
- 8 Does gas still flow when pilot light goes out?
- 9 How do I know if my gas heater is working?
- 10 How do I reset my gas heater?
- 11 What to check when heater is not working?
How do you light a gas heater in a house?
If you have a gas furnace, here are the steps on how to light a pilot light.
- First, locate the pilot valve on the furnace.
- Find the gas valve and turn it to the “off” position.
- Turn the valve to the “pilot” position.
- Press and hold the reset button.
- If the reset button fails, ignite the lighter.
Why is my gas heater not turning on?
Check the Pilot Light – A dirty or faulty pilot light is one of the main reasons a gas furnace won’t start. Reattach the pilot light, replace the panel, restore power to the furnace, and return the unit’s gas flow. If the furnace still doesn’t work, it’s time to call in the professionals.
Are indoor gas heaters safe?
Used properly, indoor propane heaters are safe. Never place anything on top of an indoor propane space heater. Install carbon monoxide detectors in your home, or the space where you use your indoor propane space heater. If you have a portable propane indoor space heater, do not move it while it is on.
What do you do when your gas heater stops working?
Furnace Not Working—No Gas Flame
- Turn off the gas shut-off valve.
- Wait 5 minutes for gas to clear.
- Locate the pilot light under the gas valve.
- Turn the gas valve to “Pilot.”
- Push the knob down to start the flow of gas to the pilot and hold it down.
- Using an extended lighter, reach into the access and light the pilot.
How does a heater work in a house?
Furnaces use forced air to distribute heat throughout your house. Inside of a furnace, air is warmed up by the fuel source. A blower then pushes the warm air through a duct system and into various rooms of a house. Cooled air returns to the furnace through a separate series of ducts, known as a return.
Why is my heat not kicking on?
Thermostat. If your furnace is not kicking on, it can be an issue with the thermostat. You should first make sure that the thermostat is switched to the heating function. You may also have an internal problem with your thermostat, which needs to be repaired by a professional.
Should the pilot light always be on in a gas heater?
Most furnaces with electronic ignition have a device called a hot surface igniter. The difference is that the flame is only lit (by an electronic spark) when your furnace is ready for a heating cycle. When the pilot light is not needed, it is completely off, saving you money on gas.
Does gas still flow when pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.
How do I know if my gas heater is working?
Your gas furnace should show no signs of wear, rust, soot, or dirt deposits. When your furnace runs, the color of theflame inside the burner should be blue. If your gas burns yellow, this may indicate it’s not getting enough oxygen and is creating carbon monoxide.
How do I reset my gas heater?
How do you restart a gas furnace?
- Turn the circuit breaker off and switch the furnace power button off too.
- Access the pilot light by removing the access panel.
- Turn the gas control valve off and let the gas dissipate for five minutes before turning it back on in order to prevent a fire hazard.
What to check when heater is not working?
1. Check that your thermostat is set to “heat.” If it doesn’t come on, set the thermostat to 90-degrees Fahrenheit so it won’t turn on and off while you are trying to fix the problem. If your thermostat doesn’t seem to be working, trace the wires back to the furnace to check for breaks.