- 1 How do you turn a pilot light back on?
- 2 How can I tell if my water heater pilot light is on?
- 3 Why can’t I light the pilot on my water heater?
- 4 How much does it cost to relight a pilot?
- 5 Do I need to turn gas off if pilot light goes out?
- 6 Should pilot light always be on water heater?
- 7 What does a blinking red light mean on a water heater?
- 8 How do you know if you have a bad thermocouple?
- 9 Can I manually light my gas water heater?
- 10 What do I do if my pilot light won’t light?
- 11 Is there a reset button on water heaters?
- 12 Why my water heater is not working?
- 13 What to check when there’s no hot water?
How do you turn a pilot light back on?
Turn the valve to the “pilot” position. Press and hold the reset button. If the reset button fails, ignite the lighter. Hold down the reset button and bring a grill lighter or long match to the pilot light valve until the pilot ignites.
How can I tell if my water heater pilot light is on?
It’s usually right on the panel. Turn and hold the knob to “Pilot” and push the ignitor. You should hear it click, and probably also a “whooshing” sound. Check in that gap, and you should see the light on.
Why can’t I light the pilot on my water heater?
The water heater pilot light is a small flame that ignites the gas burner on your water heater. If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.
How much does it cost to relight a pilot?
Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100. Have you ever relit your own pilot light?
Do I need to turn gas off if pilot light goes out?
If the pilot light goes out on a storage or instantaneous hot water heater, space heater or a ducted heater, you will not have a gas leak. This is because all modern gas appliances with pilot lights have a fail-safe device that closes off the gas to the appliance in the case when the pilot may go out.
Should pilot light always be on water heater?
The pilot should be on the water heating the house. The pilot flame can be difficult to see through a window. To know if the pilot is on or off, you need to remove the access door and shield and look at the burner and pilot through it.
1 flash every 3 seconds means the pilot is lit and the gas valve is working normally. A solid red status light means the water heater is shutting down. Remember, 1 flash every 3 seconds means the pilot is lit and the gas valve is operating normally.
How do you know if you have a bad thermocouple?
If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.
Can I manually light my gas water heater?
Lighting the Pilot Light on a Manual Hot Water Heater If your hot water heater is a manual, grab a long lighter. Turn the pilot dial to the off position and wait 5-10 minutes for any gas to dissipate. Then, turn the pilot dial until it says the word pilot. After that, set your temperate knob to low.
What do I do if my pilot light won’t light?
How to Fix Your Pilot Light
- Find your gas valve.
- You need to turn the valve to the off position for at least three minutes.
- Once you have had the valve at off for a few minutes, switch it over to pilot setting.
- You will need a match that is lit.
- Set the pilot valve to the on position.
Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. Once you find the button, push and release it.
Why my water heater is not working?
No Power or Gas If an electric water heater is not producing hot water, it could be a simple problem like a blown fuse or tripped circuit breaker. Additionally, some electric water heaters have a circuit-style safety switch located near or on the thermostat.
What to check when there’s no hot water?
Solved! What to Do When There’s No Hot Water
- Bump up the thermostat.
- Relight the pilot light.
- Fix a faulty thermocouple.
- Rekindle a blue flame.
- Inspect the gas line.
- Restart your water heater.
- Reset the circuit breaker.
- Call in the professionals.