FAQ: How To Turn On Water Heater Pilot Light?

How can I tell if my water heater pilot light is on?

It’s usually right on the panel. Turn and hold the knob to “Pilot” and push the ignitor. You should hear it click, and probably also a “whooshing” sound. Check in that gap, and you should see the light on.

Why can’t I light the pilot on my water heater?

The water heater pilot light is a small flame that ignites the gas burner on your water heater. If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.

How do you turn a pilot light back on?

How to Relight a Pilot Light: 5 Steps

  1. Find the pilot light assembly and its reset switch. The furnace’s pilot light is usually positioned at the bottom of the unit by a knob.
  2. Set the reset switch to off. Turn the knob to the “Off” setting.
  3. Wait a moment.
  4. Relight the pilot light.
  5. Observe the furnace.
You might be interested:  FAQ: How To Install Water Heater?

Do I need to turn gas off if pilot light goes out?

If the pilot light goes out on a storage or instantaneous hot water heater, space heater or a ducted heater, you will not have a gas leak. This is because all modern gas appliances with pilot lights have a fail-safe device that closes off the gas to the appliance in the case when the pilot may go out.

Should pilot light always be on water heater?

The pilot should be on the water heating the house. The pilot flame can be difficult to see through a window. To know if the pilot is on or off, you need to remove the access door and shield and look at the burner and pilot through it.

How do you know if you have a bad thermocouple?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

Can I manually light my gas water heater?

Lighting the Pilot Light on a Manual Hot Water Heater If your hot water heater is a manual, grab a long lighter. Turn the pilot dial to the off position and wait 5-10 minutes for any gas to dissipate. Then, turn the pilot dial until it says the word pilot. After that, set your temperate knob to low.

What do I do if my pilot light won’t light?

How to Fix Your Pilot Light

  1. Find your gas valve.
  2. You need to turn the valve to the off position for at least three minutes.
  3. Once you have had the valve at off for a few minutes, switch it over to pilot setting.
  4. You will need a match that is lit.
  5. Set the pilot valve to the on position.
You might be interested:  How To Turn On Water Heater In Rv?

How much does it cost to relight a pilot?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100. Have you ever relit your own pilot light?

Why is a pilot light called a pilot light?

Originally a pilot light was kept permanently alight, but this wastes gas. The term “pilot light” is also used occasionally for an electrical indicator light that illuminates to show that electrical power is available, or that an electrical device is operating.

Will you smell gas if pilot light goes out?

This system will allow a small amount of gas to leak through the pilot tubing. If the pilot light is out, the gas must be shut off at the appliance isolation valve, normally located in close proximity to the appliance. If you notice an odor of gas, contact Peoples’ emergency number at 1-800-400-4271.

Can you get carbon monoxide poisoning from a pilot light?

A pilot light should be a crisp blue colour. A yellow or orange pilot light will produce carbon monoxide – an odourless, colourless gas that can fill your home and cause carbon monoxide poisoning. Symptoms of this condition include dizziness, headache, fatigue, nausea, unconsciousness, brain damage and death.

Can a pilot light out cause carbon monoxide?

Carbon monoxide is only produced when fuel of any type; oil, gas, wood or coal is burned. And a pilot light out of adjustment can produce carbon monoxide gas. The amount produced by even a badly maladjusted pilot is small because the flame size is also small.

Leave a Reply

Your email address will not be published. Required fields are marked *