- 1 How do you light a pilot light on a Williams heater?
- 2 How do I get my pilot light to work?
- 3 Where is the pilot light on a wall heater?
- 4 How do you reset a Williams wall heater?
- 5 Can I relight my own pilot light?
- 6 How do you reset the pilot light?
- 7 What do you do when the pilot light goes out on your water heater?
- 8 What do I do if my pilot light won’t light?
- 9 How do I know if my thermocouple is bad?
- 10 What do I do if my water heater won’t light?
- 11 Can I turn off my pilot light?
- 12 Does gas turn off when pilot goes out?
- 13 Is it safe to leave pilot light on wall heater?
How do you light a pilot light on a Williams heater?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light.
How do I get my pilot light to work?
To relight the pilot light, you have to push a button that opens the value manually. Then you light the pilot light and wait for the thermocouple to heat up (about 30 seconds). Once it is hot, the thermocouple is generating the electricity needed to hold the value open. Then you can let go of the button.
Where is the pilot light on a wall heater?
In some heaters, it is easy to locate the pilot light, as it is just behind the heater vent. For others, you will have to open the cover of the burner area or remove it altogether, then follow the gas connection from the main gas supply to the pilot light. The pilot light is inside the heater, behind a metal plate.
How do you reset a Williams wall heater?
1) Unscrew 3 mounting screws (1 on top and 2 on inside bottom by gas valve assemply) and pull cover/housing back. 2) Turn on thermostat. 3) Press/hold RED reset button (upper top left side of heater assembly; two wires were connected to it) for about 2 seconds. It immediately fired up.
Can I relight my own pilot light?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
How do you reset the pilot light?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.
What do you do when the pilot light goes out on your water heater?
What should you do when your water heater’s pilot light goes out?
- Turn the thermostat to the lowest setting.
- Turn the on/off/pilot switch to the “pilot” position.
- Remove the outer and inner panels to access your pilot light.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
How do I know if my thermocouple is bad?
If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.
What do I do if my water heater won’t light?
If you have a natural or propane gas water heater, chances are the pilot has gone out. If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.
Can I turn off my pilot light?
Turn off the light. Often, turning off the pilot light is as simple as turning a knob to “off.” For other systems, you may have to push a small lever out of the way in order to turn the knob. Whatever you do, don’t force the knob. This could result in costly repairs.
Does gas turn off when pilot goes out?
The pilot light provides a small flame that ignites the gas needed to operate the appliance. This is because all modern gas appliances with pilot lights have a fail-safe device that closes off the gas to the appliance in the case when the pilot may go out. The fail-safe device is comprised of a thermocouple.
Is it safe to leave pilot light on wall heater?
When you turn off your pilot light, the light’s tubes will maintain a trace level of mercaptan, and that will attract spiders, who will spin webs that can clog the pilot light system. Leaving the gas on keeps this compound moving out of the tubes.