Often asked: How To Light A Water Heater Pilot?

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

What causes a pilot light to go out on a water heater?

Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple. Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it’s burning properly. A bent or dirty thermocouple.

Is it safe to light pilot on water heater?

Before You Strike a Flame If so, attempting to light the pilot at this point is extremely dangerous and could cause an explosion. Turn off the gas line to your water heater and wait 1 hour. Turn the gas back on, wait 10 minutes, and sniff again. If the problem persists, call a qualified gas technician.

You might be interested:  FAQ: How To Test A Water Heater Thermostat?

How much does it cost to relight a pilot?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100. Have you ever relit your own pilot light?

How do you know if you have a bad thermocouple?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

How much does it cost to replace a thermocouple on a water heater?

Thermocouple – $20 to $150 The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average.

Will gas leak if pilot light is off?

If the pilot light goes out on a storage or instantaneous hot water heater, space heater or a ducted heater, you will not have a gas leak. This is because all modern gas appliances with pilot lights have a fail-safe device that closes off the gas to the appliance in the case when the pilot may go out.

Can I manually light my gas water heater?

Lighting the Pilot Light on a Manual Hot Water Heater If your hot water heater is a manual, grab a long lighter. Turn the pilot dial to the off position and wait 5-10 minutes for any gas to dissipate. Then, turn the pilot dial until it says the word pilot. After that, set your temperate knob to low.

You might be interested:  Quick Answer: How Long Does A Water Heater Take To Heat Water?

Do pilot lights smell?

Note that it is totally normal on automatic pilots (pilots that do NOT stay lit all the time) to smell a little natural gas when the are first turned on. A little gas will escape as the pilot and burners light on your heat or appliance.

Can a water heater explode?

Water heater explosions are terrifying, and they can happen. Anything that causes excess pressure on your water heating system, such as a poor anode rod, or a lot of sediment buildup, can all cause your water heater to explode. A gas leak can also cause your water heater to explode because it is a tremendous fire risk.

What do I do if my pilot light won’t light?

How to Fix Your Pilot Light

  1. Find your gas valve.
  2. You need to turn the valve to the off position for at least three minutes.
  3. Once you have had the valve at off for a few minutes, switch it over to pilot setting.
  4. You will need a match that is lit.
  5. Set the pilot valve to the on position.

How do you reset the pilot light?

Turn the valve to the “pilot” position. Press and hold the reset button. If the reset button fails, ignite the lighter. Hold down the reset button and bring a grill lighter or long match to the pilot light valve until the pilot ignites.

What does a pilot light look like in oven?

Locate and light the pilot light: It’s often labeled “pilot light,” and can be a small hole in the bottom of the oven, front center near the door opening, or in a back corner. If you don’t see it inside the oven, it could be in the back of the broiler compartment. Use a microfiber cloth to wipe down the area.

Leave a Reply

Your email address will not be published. Required fields are marked *