Often asked: How To Light Pilot On Hot Water Heater?

How do you light a pilot light on a water heater?

Lighting the Pilot Light on an Automatic Hot Water Heater All you have to do is hold the pilot knob down for 30 seconds and hold the ignition button at the same time. You do not need to use a lighter. Your pilot light will turn on!

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

Is it safe to light pilot on water heater?

Before You Strike a Flame If so, attempting to light the pilot at this point is extremely dangerous and could cause an explosion. Turn off the gas line to your water heater and wait 1 hour. Turn the gas back on, wait 10 minutes, and sniff again. If the problem persists, call a qualified gas technician.

You might be interested:  How Does A Water Heater Work Internally?

How do you light a hot water heater with an igniter?

Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot. Then, turn the On/Off/Pilot dial downwards and push the igniter button at the same time. Let go of the igniter button, but keep pressing the Pilot dial downward for around 30 seconds. You should hear a “whoosh” sound when the gas is lit.

How do I know if my pilot light is out on my water heater?

No flame where there should be a flame? These are signs the pilot light on your water heater is out. Fortunately, it’s a really easy fix. Signs your pilot light is out

  1. Your Water is Cold.
  2. Blinking Light or Error Message.
  3. You Can’t See the Flame.

What do I do if my pilot light won’t light?

How to Fix Your Pilot Light

  1. Find your gas valve.
  2. You need to turn the valve to the off position for at least three minutes.
  3. Once you have had the valve at off for a few minutes, switch it over to pilot setting.
  4. You will need a match that is lit.
  5. Set the pilot valve to the on position.

How much does it cost to relight a pilot?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100. Have you ever relit your own pilot light?

What causes a water heater pilot to go out?

Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple. Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it’s burning properly. A bent or dirty thermocouple.

You might be interested:  Often asked: 2005 Altima Heater Only Hot When Accelerating?

Why is a pilot light called a pilot light?

Originally a pilot light was kept permanently alight, but this wastes gas. The term “pilot light” is also used occasionally for an electrical indicator light that illuminates to show that electrical power is available, or that an electrical device is operating.

Can a water heater explode?

Water heater explosions are terrifying, and they can happen. Anything that causes excess pressure on your water heating system, such as a poor anode rod, or a lot of sediment buildup, can all cause your water heater to explode. A gas leak can also cause your water heater to explode because it is a tremendous fire risk.

Why do I suddenly have no hot water?

If there is no hot water, it probably means that the tank is leaking. An empty tank is a serious problem and is not at all energy efficient. Inspect the connections between the appliance and its valves as well as the pipes. If those are secure, check the tank’s compartment.

What happens if my water heater pilot light goes out?

If the pilot light goes out, your water heater won’t be able to ignite the gas burner and therefore, won’t be able to heat the water. In fact, often the first clue your pilot light is out is the discovery that you don’t have hot water.

How do you know if you have a bad thermocouple?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

You might be interested:  FAQ: Where Is The Block Heater On A 6.6 Duramax?

What do you do when you have no hot water?

Solved! What to Do When There’s No Hot Water

  1. Bump up the thermostat.
  2. Relight the pilot light.
  3. Fix a faulty thermocouple.
  4. Rekindle a blue flame.
  5. Inspect the gas line.
  6. Restart your water heater.
  7. Reset the circuit breaker.
  8. Call in the professionals.

How do you relight an automatic pilot light?

How to Relight an Automatic Pilot Light

  1. Set the thermostat on your furnace to its lowest setting.
  2. Remove the access panel covering the gas control knob.
  3. Turn the gas control knob to the OFF position.
  4. Turn the gas control knob or knobs to the ON position.
  5. Turn the electrical power to the furnace back on.

Leave a Reply

Your email address will not be published. Required fields are marked *