Often asked: How To Light Water Heater Pilot Light?

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

Is it safe to light pilot on water heater?

Before You Strike a Flame If so, attempting to light the pilot at this point is extremely dangerous and could cause an explosion. Turn off the gas line to your water heater and wait 1 hour. Turn the gas back on, wait 10 minutes, and sniff again. If the problem persists, call a qualified gas technician.

How do you light a hot water heater with an igniter?

Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot. Then, turn the On/Off/Pilot dial downwards and push the igniter button at the same time. Let go of the igniter button, but keep pressing the Pilot dial downward for around 30 seconds. You should hear a “whoosh” sound when the gas is lit.

You might be interested:  FAQ: What Is A Good Temperature For Your Heater?

What happens if water heater pilot light goes out?

If the pilot light goes out, your water heater won’t be able to ignite the gas burner and therefore, won’t be able to heat the water. But once the pilot light is relit, the water heater is able to ignite the gas burner and can begin to heat the water again.

What do you do if the pilot light goes out?

Your pilot light relies on your natural gas to stay aflame, so if your gas is shut off, your pilot light will go out. Simply turn your gas back on and either relight your pilot light yourself or call a professional.

How much does it cost to relight a pilot?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100. Have you ever relit your own pilot light?

Can I manually light my gas water heater?

Lighting the Pilot Light on a Manual Hot Water Heater If your hot water heater is a manual, grab a long lighter. Turn the pilot dial to the off position and wait 5-10 minutes for any gas to dissipate. Then, turn the pilot dial until it says the word pilot. After that, set your temperate knob to low.

Why do I suddenly have no hot water?

If there is no hot water, it probably means that the tank is leaking. An empty tank is a serious problem and is not at all energy efficient. Inspect the connections between the appliance and its valves as well as the pipes. If those are secure, check the tank’s compartment.

You might be interested:  Question: How Long Do Hot Water Heater Elements Last?

Can a water heater explode?

Water heater explosions are terrifying, and they can happen. Anything that causes excess pressure on your water heating system, such as a poor anode rod, or a lot of sediment buildup, can all cause your water heater to explode. A gas leak can also cause your water heater to explode because it is a tremendous fire risk.

How do you know if you have a bad thermocouple?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

How do you relight an automatic pilot light?

How to Relight an Automatic Pilot Light

  1. Set the thermostat on your furnace to its lowest setting.
  2. Remove the access panel covering the gas control knob.
  3. Turn the gas control knob to the OFF position.
  4. Turn the gas control knob or knobs to the ON position.
  5. Turn the electrical power to the furnace back on.

How do you light a hot water heater without an igniter?

Lighting with No Igniter

  1. Take a long lighter to reach the pilot.
  2. Remove the plate attached below the dial box.
  3. Switch Pilot to OFF.
  4. Wait for a while, – 5-10 minutes until there won’t be any gas.
  5. Change the temperature to LOW, and switch to Pilot.
  6. Push ON/OFF dial down, and simultaneously use the lighter.

What causes a water heater pilot to go out?

Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple. Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it’s burning properly. A bent or dirty thermocouple.

You might be interested:  Often asked: What Should The Water Heater Be Set At?

Do I need to turn gas off if pilot light goes out?

If the pilot light goes out on a storage or instantaneous hot water heater, space heater or a ducted heater, you will not have a gas leak. This is because all modern gas appliances with pilot lights have a fail-safe device that closes off the gas to the appliance in the case when the pilot may go out.

Can you get carbon monoxide poisoning from a pilot light?

A pilot light should be a crisp blue colour. A yellow or orange pilot light will produce carbon monoxide – an odourless, colourless gas that can fill your home and cause carbon monoxide poisoning. Symptoms of this condition include dizziness, headache, fatigue, nausea, unconsciousness, brain damage and death.

Leave a Reply

Your email address will not be published. Required fields are marked *