Often asked: How To Start The Pilot Light On A Water Heater?

What do you do when the pilot light goes out on your water heater?

What should you do when your water heater’s pilot light goes out?

  1. Turn the thermostat to the lowest setting.
  2. Turn the on/off/pilot switch to the “pilot” position.
  3. Remove the outer and inner panels to access your pilot light.

Why can’t I light the pilot on my water heater?

The water heater pilot light is a small flame that ignites the gas burner on your water heater. If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.

Do I need to turn gas off if pilot light goes out?

If the pilot light goes out on a storage or instantaneous hot water heater, space heater or a ducted heater, you will not have a gas leak. This is because all modern gas appliances with pilot lights have a fail-safe device that closes off the gas to the appliance in the case when the pilot may go out.

You might be interested:  Quick Answer: How To Drain An Electric Water Heater?

Should pilot light always be on water heater?

The pilot should be on the water heating the house. The pilot flame can be difficult to see through a window. To know if the pilot is on or off, you need to remove the access door and shield and look at the burner and pilot through it.

How do you know if you have a bad thermocouple?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

Can I manually light my gas water heater?

Lighting the Pilot Light on a Manual Hot Water Heater If your hot water heater is a manual, grab a long lighter. Turn the pilot dial to the off position and wait 5-10 minutes for any gas to dissipate. Then, turn the pilot dial until it says the word pilot. After that, set your temperate knob to low.

Can you manually light a water heater with electronic pilot?

* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system. If the pilot light will not re-light, the problem could be a clogged pilot line or orifice, or gas is not reaching the water heater.

Will you smell gas if pilot light goes out?

This system will allow a small amount of gas to leak through the pilot tubing. If the pilot light is out, the gas must be shut off at the appliance isolation valve, normally located in close proximity to the appliance. If you notice an odor of gas, contact Peoples’ emergency number at 1-800-400-4271.

You might be interested:  Quick Answer: What Is The Best Temperature Setting For A Hot Water Heater?

Can a pilot light relight itself?

Relighting a pilot light may be possible, depending on the type you have. By design, an automatic pilot light does not need to be lighted or relighted; it turns on and off by itself. If an automatic pilot or igniter is failing to light the burners on your appliance, it typically needs to be replaced.

Can you get carbon monoxide poisoning from a pilot light?

A pilot light should be a crisp blue colour. A yellow or orange pilot light will produce carbon monoxide – an odourless, colourless gas that can fill your home and cause carbon monoxide poisoning. Symptoms of this condition include dizziness, headache, fatigue, nausea, unconsciousness, brain damage and death.

How much does it cost to replace a thermocouple?

The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average.

Should I leave my gas water heater on all the time?

It only takes a tiny spark to ignite highly combustible propane gas – which can mean an explosion or fire in case of accident. The simple and safe answer that you should not leave your RV hot water heater on all the time if it is propane powered.

Can I leave my hot water tank on pilot?

3 Answers. Yes it is safe to leave the water heater in pilot mode while flushing. You do not want the burner to fire while the tank is empty as this can damage the tank but the pilot will not cause a problem. Added: most gas valves with a standing pilot have the temp setting and “pilot” then off settings.

Leave a Reply

Your email address will not be published. Required fields are marked *