Often asked: What Temperature Should I Set My Hot Water Heater?

Is 140 too hot for water heater?

The Occupational Safety & Health Administration (OSHA) recommends water heaters be set to at least 140 degrees Fahrenheit (60 degrees Celsius) to minimize the growth of Legionella and other microorganisms.

Is 130 too hot for water heater?

Professionals recommend keeping your water heater set at a temperature between 130 and 140 degrees Fahrenheit. Any higher, or lower, could actually be dangerous for you and your family. While turning the temperature up higher can result in burns, turning it lower than the recommended setting can also be dangerous.

What should my hot water tank thermostat be set at?

The short answer: 120 degrees Fahrenheit. This is the preset thermostat temperature in most new water heaters, and it’s the recommended setting of the U.S. Department of Energy. At this temperature, harmful pathogens like the kind that cause Legionnaires’ disease are prevented from multiplying and may be killed.

You might be interested:  Question: How To Adjust Gas Hot Water Heater Thermostat?

What is the best temperature for hot water heater?

So, what is the best temperature range for your water heater? The EPA recommends 120 degrees because it’s hot enough to keep diseases at bay, it’s not hot enough to cause scalding, it will supply enough hot water for most small families and is relatively energy-efficient.

Is 50 degrees hot enough for hot water?

Water that is 57 degrees can cause a major burn within a few seconds. This highlights just how dangerous water can be over the 50 degree temperature mark even if it is only a few degrees. In the case of how hot is too hot, the absolute maximum should be 50 degrees for every appliance located in a bathroom area.

Is 150 too hot for water heater?

The recommended setting for household water heaters is not 150 degrees, but slightly less _ 140 degrees. Water temperatures higher than 140 degrees can burn the skin and are particularly dangerous for young children and the elderly. People with poor circulation can scald themselves without knowing it.

Is 135 too hot for water heater?

The American Society of Sanitary Engineering recommends that hot water tanks be set from 135 to 140 degrees, to inhibit the growth of Legionella bacteria, with the installation of anti-scald devices and tempering valves to prevent hot water injuries.

Is 125 too hot for hot water heater?

If you invest in one or more thermal protection devices to protect against overly hot water, the water heater could be safely set a little higher than 125 degrees. Most water heaters don’t have a thermostat control that is calibrated in such a way that you can just dial in 125 degrees.

You might be interested:  Often asked: What Size Copper Pipe For Hot Water Heater?

Can bacteria grow in a hot water heater?

There are a few bacteria that are likely to grow in your water heater, but the most common is legionella. Legionella is the bacteria that causes Legionnaires’ disease. You can get Legionnaires’ disease by inhaling microdroplets of legionella-contaminated water. Legionnaires’ disease is a severe type of pneumonia.

Does turning up water heater make hot water last longer?

Turn up the thermostat on the hot water heater. One of the easiest ways to make a hot shower last longer is by using less hot water while it’s at a higher temperature. To do this, turn up the temperature on the thermostat that’s attached to the hot water heater tank. Be conscious of other hot water in your home.

Does turning down the temperature on a water heater save money?

Homeowners will find that by turning down their hot water tank temperature by about 20 degrees to 120 Fahrenheit or 48 Celsius, they will see cost savings of about 6 to 10 percent.

Where is the thermostat in a hot water heater?

Most water heaters have two thermostats. The are attached to the side of the tank. The locations of the thermostats are beside two removable plates on the side of the water heater. You have to remove the metal covers on the outside of the hot water tank first.

How long does it take a hot water heater to heat up?

The average gas heater takes between 30 and 40 minutes to fully heat up the water in its tank. The average electric heater takes about twice as long as the average gas heater to fully heat up the water in its tank, so you can expect it to take between an hour and an hour and 20 minutes to heat up.

Leave a Reply

Your email address will not be published. Required fields are marked *