Question: How To Light A Pilot Light On A Water Heater?

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

What causes a pilot light to go out on a water heater?

Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple. Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it’s burning properly. A bent or dirty thermocouple.

How much does it cost to relight a pilot?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100. Have you ever relit your own pilot light?

What do I do if pilot light goes out?

Your pilot light relies on your natural gas to stay aflame, so if your gas is shut off, your pilot light will go out. Simply turn your gas back on and either relight your pilot light yourself or call a professional.

You might be interested:  Question: How To Shop For A Water Heater?

How do you know if you have a bad thermocouple?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

Should pilot light always be on water heater?

The pilot should be on the water heating the house. The pilot flame can be difficult to see through a window. To know if the pilot is on or off, you need to remove the access door and shield and look at the burner and pilot through it.

How much does it cost to replace a thermocouple on a water heater?

Thermocouple – $20 to $150 The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average.

Does gas leak if the pilot light goes out?

When the pilot light goes out, it does not leak carbon monoxide gas. Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds.

Does leaving your pilot light use much gas?

How much gas does a pilot light require? Most pilot lights consume around 600 BTUs of gas every hour. If you leave your pilot light on for an entire day, it would roughly consume 14,400 BTU’s every day.

You might be interested:  Often asked: How Long To Refill Water Heater?

How much does a pilot light cost per month?

– Reduced energy costs The pilot light burns significantly less fuel than a fire but it can cost $8 to $10 a month if your fireplace is fueled by natural gas. If your fireplace is fueled by propane, it could cost up to $20 a month. Turning off the pilot would reduce your energy costs during the summer.

How can I tell if my pilot light is out?

How to Tell If the Pilot Light Is Out

  1. Locate the front cover panel on your furnace. It should be a little door that’s easily visible.
  2. If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame.
  3. If you don’t see a flame, your pilot light is out.
  4. If there is a flame, check the color.

Can you get carbon monoxide poisoning from a pilot light?

A pilot light should be a crisp blue colour. A yellow or orange pilot light will produce carbon monoxide – an odourless, colourless gas that can fill your home and cause carbon monoxide poisoning. Symptoms of this condition include dizziness, headache, fatigue, nausea, unconsciousness, brain damage and death.

How do you clean a pilot light?

How to Clean a Pilot Light

  1. Cut off the gas to your furnace.
  2. Remove the pilot light and thermocouple assembly.
  3. Use your pliers or wrench to remove the pilot light and thermocouple from the bracket.
  4. Using the wire brush, brush away the carbon buildup and soot from both components.

Leave a Reply

Your email address will not be published. Required fields are marked *