Quick Answer: How To Clean Thermocouple On Water Heater?

How do you clean a dirty thermocouple?

The best way to clean your thermocouple is to use either a piece of steel wool or the coarse side of a sponge to gently clean off any soot or other remnants. You can use a pencil eraser to clean between the threads of the screw that connects the thermocouple to the control valve of your system.

How do I know if my thermocouple is bad on my water heater?

If the pilot lights but the flame goes out as soon as you release the button after holding it for 60 seconds, then the thermocouple is bad. It’s possible to replace the thermocouple without removing the burner assembly, and many repair people do this.

Should you clean a thermocouple?

If the Thermocouple is faulty it will cause the unit to shut down. How to clean? Remove Thermocouple from pilot assembly, using steel wool or emery cloth to lightly clean the tip removing any soot or build up that might have accorded due to an improper pilot flame.

You might be interested:  What Size Electric Heater Do I Need?

How often should you replace a thermocouple?

The thermocouple unwinds and switches on the fireplace. Thermocouples are rigorously tested and should last for years. Indeed, experts believe a four-year check cycle is all that is needed to make sure things are functioning properly.

How do I clean thermopile thermocouple?

To quickly clean your thermopile, turn off the gas supply. With the help of a stainless steel brush and fine-grit sandpaper, you can scrub off as much piled up soot as possible.

What are the symptoms of a bad thermocouple?

Failed Thermocouple Symptoms

  • Signs of contamination on the tube, e.g. discoloration, cracks, or pinholes.
  • Signs of wear or corrosion of the wirings, e.g. missing insulation or bare wire.
  • Physical damage to the connectors which can have an effect on the reliability of the test reading.

Can you replace a thermocouple yourself?

The No. 1 cause of pilot lights that won’t stay lit is a worn-out thermocouple. It’s easy to replace and a new one costs $5 to $10. Then unfasten the three nuts that hold the thermocouple and the two gas tubes to the valve.

How much does it cost to replace a water heater thermocouple?

Thermocouple – $20 to $150 The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average.

Why do thermocouples go bad?

Changes in temperature can cause regular expansion and contraction in metal, which will cause thermocouples to weaken over time. After enough time, metal fatigue can cause a thermocouple to break. If thermocouples start to give out unusual readings, it may be suffering from metal fatigue.

You might be interested:  Quick Answer: How To Program Heater Thermostat?

Can a thermocouple be too long?

The length of a thermocouple has no effect on its measurement accuracy or its ability to transfer the signal to the instrument. In reality the sensor can be inches or thousands of feet long and the accuracy will not be affected.

How do you fix a pilot light that keeps going out?

What do I do if my pilot light keeps going out?

  1. Find the gas shut-off knob and turn to the “Off” setting.
  2. Remove the access panel to access the burner.
  3. Turn the knob to “Pilot” to start the flow of gas.
  4. While still holding the gas knob, light the pilot with a long lighter.

How do you check if a thermocouple is working?

If the thermocouple is working, you should be able to measure 30 to 40 millivolts of voltage at the connection end of the tube when the pilot flame is on. You can test this yourself using a multimeter, but you may need a helper to keep the pilot flame burning while you do it.

Are hot water heater thermocouples universal?

Universal Thermocouples. Universal thermocouples, as the name implies work on most water heaters. They are available online and in home supply stores for a reasonable cost. The length and the thread type are the two concerns when purchasing one.

Leave a Reply

Your email address will not be published. Required fields are marked *