Quick Answer: How To Light A Pilot Light On A Wall Heater?

How do I light the pilot on my wall heater?

Electric Heaters For new wall heaters, turn the dial towards ‘Pilot’ and press down on the ‘Ignite’ button. You will have to press the button, again and again, until the pilot light starts from the spark. When the pilot light starts, continue holding the button for about a minute. Then, release it.

How do you ignite a gas wall heater?

Steps For Safely Lighting a Gas Wall Heater

  1. Have a match or long lighter available to light the pilot.
  2. Find the valve located in the heater and turn it to “Pilot”.
  3. Press inward on the valve. You should hear a hissing sound coming from the valve.
  4. Release the valve and light your match.
  5. Release the valve after one minute.

Can a pilot light cause carbon monoxide?

A yellow or orange pilot light will produce carbon monoxide – an odourless, colourless gas that can fill your home and cause carbon monoxide poisoning. Symptoms of this condition include dizziness, headache, fatigue, nausea, unconsciousness, brain damage and death.

You might be interested:  Question: What Is Ptc Heater Element?

Why is my wall heater not working?

If your heater’s not working at all, check for a tripped breaker or blown fuse. Reset the breaker or replace the blown fuse, if necessary. If the problem isn’t with the breaker box, examine the unit’s wiring for loose connections. If you still can’t get the heater working again, it probably needs a new heating element.

How do I turn on my gas wall heater in my apartment?

How to Turn On a Wall Heater

  1. To turn on your gas heater, locate the knob for starting.
  2. Turn the knob to “Pilot,” and then push down on the “Ignite” button.
  3. Once the pilot light comes on, hold down the Ignite button for 10 to 15 seconds.
  4. Set the temperature on the wall heater to your desired heating level.

Should the pilot light always be on in a gas furnace?

If you have an older gas furnace, your heating unit relies on a little blue flame known as a pilot light to ensure ignition of the burners. Since the pilot light needs to remain active, your furnace is always consuming some gas.

How do you fix a pilot light on a gas heater?

Gas Heater Pilot Light Troubleshooting

  1. Check the Thermocouple. If your pilot light won’t stay alight, it might be the thermocouple.
  2. Adjust an Irregular Flame. If your pilot light is flickering and faint, you might need to adjust the flame.
  3. Check the Gas Levels.
  4. Check for a Corroded Pilot Tip.
  5. Regulate any Draft.

Can you light a gas heater with a lighter?

Yes, it is safe to light a pilot light with a gas lighter. Then, turn the burner knob to the ‘pilot’ position. Now, keeping the knob in that position, light the pilot light using a gas lighter. After that, you can turn the burner knob to the ‘on’ position and adjust the flame as you like.

You might be interested:  Often asked: How To Replace Defrost Heater In Refrigerator?

Is it bad if the pilot light goes out?

The pilot light is a small, blue flame that is used to ignite the natural gas being pumped into the main burner. This tube is fitted with a safety valve (the thermocouple), which stops the flow of gas if the pilot light goes out. This prevents gas from building up in your furnace, posing a safety hazard.

Is it OK to leave pilot light off?

When a pilot light burns for long periods of time (like during the summer) without igniting the main burner, a film can develop on the glass doors of the fireplace. This film is sulfur-based and if not cleaned off, it can permanently damage the glass.

What color should my pilot light be?

The color of the pilot light should be blue because that means that only natural gas—without any other condensates—is reaching the pilot light through the gas main. The principal chemical compound found in natural gas is methane, and methane burns blue.

Leave a Reply

Your email address will not be published. Required fields are marked *