Quick Answer: How To Light A Whirlpool Hot Water Heater?

How do you light the pilot on a Whirlpool water heater?

When lighting the pilot, make sure the knob on the gas control valve is fully pushed in. Keep the knob pushed in while repeatedly clicking the spark igniter button. Hold the knob in and click the igniter button repeatedly for 90 seconds. Newly installed water heaters have air in the gas line.

How do I light the pilot on my hot water heater?

How to Light a Water Heater Pilot Light

  1. Open the door/cover over the pilot light access.
  2. Use a flashlight or a headlamp to find the burner inside.
  3. Turn the gas knob to “Pilot,” press and hold it down.
  4. While still holding the gas down, light that pilot.

How do you know if the pilot light is out on a Whirlpool water heater?

When lighting the pilot, make sure the knob on the gas control valve is set to Pilot and if fully pushed in. Keep the knob pushed in while clicking the spark igniter button. If the pilot still will not light, turn the gas control knob OFF, turn the gas supply valve OFF, and click on “More Help” below.

You might be interested:  FAQ: What Is A Tankless Water Heater And How Does It Work?

Where is the reset button on my Whirlpool water heater?

A water heater reset button, usually red, is located in the center of the limit switch just above the water heater thermostat. The water heater limit switch is a safety device that will shut the power down to the water heater if something malfunctions and the water gets to hot.

What do I do if my water heater won’t light?

If you have a natural or propane gas water heater, chances are the pilot has gone out. If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.

Why is my Whirlpool water heater not working?

Make sure both thermostats are pressed firmly against the tank. Check the power at the upper thermostat connection terminals that transfer power to the lower thermostat. If no power shows, the lower thermostat has failed. If there is power but no heat at either element, then that element is bad.

How long do water heaters last?

How Long Do Water Heaters Last? Based on the manufacturer’s suggested service life, the life expectancy of a water heater is about eight to 12 years. That varies with the location and design of the unit, quality of installation, maintenance schedule and water quality.

Why can’t I reset my water heater?

What do you do if the water heater reset button doesn’t reset? You might have a faulty thermostat. If the hot water heater keeps tripping the reset button, the cause may be the high limit switch. What’s happening is that the thermostat is not properly managing the heat.

You might be interested:  Quick Answer: What Does An Expansion Tank Do On A Water Heater?

Where is the pilot light on an electric water heater?

This is typically located under the gas valve, although some models will have an open gap where you can see the pilot light burning. If your water heater does not have an open gap, it is sealed burner assembly. DO NOT attempt to remove the cover.

How do you light a hot water heater without an igniter?

Lighting with No Igniter

  1. Take a long lighter to reach the pilot.
  2. Remove the plate attached below the dial box.
  3. Switch Pilot to OFF.
  4. Wait for a while, – 5-10 minutes until there won’t be any gas.
  5. Change the temperature to LOW, and switch to Pilot.
  6. Push ON/OFF dial down, and simultaneously use the lighter.

How do I know if the pilot light is out on my water heater?

It’s usually right on the panel. Turn and hold the knob to “Pilot” and push the ignitor. You should hear it click, and probably also a “whooshing” sound. Check in that gap, and you should see the light on.

Can you manually light a water heater with electronic pilot?

* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system. If the pilot light will not re-light, the problem could be a clogged pilot line or orifice, or gas is not reaching the water heater.

Leave a Reply

Your email address will not be published. Required fields are marked *