- 1 How do you start a pilot light on a heater?
- 2 How do I get my pilot light to work?
- 3 Does heater have to be on to light pilot?
- 4 Can I relight the pilot light by myself?
- 5 What do I do if my pilot light won’t light?
- 6 How do I know if my thermocouple is bad?
- 7 Is it safe to leave pilot light on wall heater?
- 8 Does pilot light stay on all the time?
- 9 Can you manually light a water heater with electronic pilot?
- 10 Does gas still flow when pilot light goes out?
- 11 How much does it cost to relight a pilot?
- 12 How do I reset my pilot light?
How do you start a pilot light on a heater?
If you have a gas furnace, here are the steps on how to light a pilot light.
- First, locate the pilot valve on the furnace.
- Find the gas valve and turn it to the “off” position.
- Turn the valve to the “pilot” position.
- Press and hold the reset button.
- If the reset button fails, ignite the lighter.
How do I get my pilot light to work?
To relight the pilot light, you have to push a button that opens the value manually. Then you light the pilot light and wait for the thermocouple to heat up (about 30 seconds). Once it is hot, the thermocouple is generating the electricity needed to hold the value open. Then you can let go of the button.
Does heater have to be on to light pilot?
Most furnaces with electronic ignition have a device called a hot surface igniter. The difference is that the flame is only lit (by an electronic spark) when your furnace is ready for a heating cycle. When the pilot light is not needed, it is completely off, saving you money on gas. You can read more about furnaces.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
How do I know if my thermocouple is bad?
If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.
Is it safe to leave pilot light on wall heater?
When you turn off your pilot light, the light’s tubes will maintain a trace level of mercaptan, and that will attract spiders, who will spin webs that can clog the pilot light system. Leaving the gas on keeps this compound moving out of the tubes.
Does pilot light stay on all the time?
Generally speaking, it is safe to leave your continuous pilot light on at all times, assuming it stays lit (more on this in a moment). While it does cost more to keep your pilot light on in between uses, it can actually have some benefits to your system.
Can you manually light a water heater with electronic pilot?
* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system. If the pilot light will not re-light, the problem could be a clogged pilot line or orifice, or gas is not reaching the water heater.
Does gas still flow when pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.
How much does it cost to relight a pilot?
Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100. Have you ever relit your own pilot light?
How do I reset my pilot light?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.