Quick Answer: How To Light Pilot On Water Heater?

How do you light a pilot light on a water heater?

Lighting the Pilot Light on an Automatic Hot Water Heater All you have to do is hold the pilot knob down for 30 seconds and hold the ignition button at the same time. You do not need to use a lighter. Your pilot light will turn on!

How do you reignite a water heater?

How to Reignite a Gas Water Heater in 7 Steps

  1. Open the door or cover that is protecting the pilot light access.
  2. Use a flashlight or headlamp to locate the burner.
  3. Gently turn the gas knob to the “Pilot” setting and hold it down.
  4. While holding the gas knob or button down, light the pilot.

What causes a pilot light to go out on a water heater?

If the pilot light goes out, the thermocouple senses the drop in temperature and signals for the gas valve to close. If you have a faulty thermocouple is the most common reason that your pilot light is malfunctioning. Over time your water heater will collect dirt, dust and other kinds of debris.

You might be interested:  Often asked: What Is The Best Heater For An Above Ground Pool?

Is it safe to light pilot on water heater?

Before You Strike a Flame If so, attempting to light the pilot at this point is extremely dangerous and could cause an explosion. Turn off the gas line to your water heater and wait 1 hour. Turn the gas back on, wait 10 minutes, and sniff again. If the problem persists, call a qualified gas technician.

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

Can you manually light an automatic pilot light?

By design, an automatic pilot light does not need to be lighted or relighted; it turns on and off by itself. Only a pilot light with a continuously burning flame — called a standing pilot— requires manual relighting if the pilot flame goes out.

How long do water heaters last?

How Long Do Water Heaters Last? Based on the manufacturer’s suggested service life, the life expectancy of a water heater is about eight to 12 years. That varies with the location and design of the unit, quality of installation, maintenance schedule and water quality.

Who do I call for water heater problems?

But for the most part, you should call a licensed plumber for all hot water heater problems.

How long does it take for water to heat up after lighting pilot?

The average gas heater takes between 30 and 40 minutes to fully heat up the water in its tank.

You might be interested:  Question: How To Check Heating Element On Water Heater?

How do you know if you have a bad thermocouple?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

How much does it cost to replace a thermocouple on a water heater?

Thermocouple – $20 to $150 The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average.

Can I replace a thermocouple myself?

It’s easy to replace and a new one costs $5 to $10. Rather than trying to unfasten the thermocouple inside the water heater’s burning chamber, it’s easier to remove the whole burner and thermocouple assembly. Then unfasten the three nuts that hold the thermocouple and the two gas tubes to the valve.

Can a water heater explode?

Water heater explosions are terrifying, and they can happen. Anything that causes excess pressure on your water heating system, such as a poor anode rod, or a lot of sediment buildup, can all cause your water heater to explode. A gas leak can also cause your water heater to explode because it is a tremendous fire risk.

Do pilot lights smell?

Note that it is totally normal on automatic pilots (pilots that do NOT stay lit all the time) to smell a little natural gas when the are first turned on. A little gas will escape as the pilot and burners light on your heat or appliance.

You might be interested:  Quick Answer: In A Fish Tank A Small Heater In One Corner Makes All The Water Warm How?

Why do I suddenly have no hot water?

If there is no hot water, it probably means that the tank is leaking. An empty tank is a serious problem and is not at all energy efficient. Inspect the connections between the appliance and its valves as well as the pipes. If those are secure, check the tank’s compartment.

Leave a Reply

Your email address will not be published. Required fields are marked *