Quick Answer: How To Relight Pilot On Water Heater?

How do you relight a pilot light on a water heater?

How to Light a Water Heater Pilot Light

  1. Open the door/cover over the pilot light access.
  2. Use a flashlight or a headlamp to find the burner inside.
  3. Turn the gas knob to “Pilot,” press and hold it down.
  4. While still holding the gas down, light that pilot.

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

Is it safe to relight water heater pilot?

Do not attempt to relight a water heater pilot light (or any other work on the unit) if you smell gas in the area, indicating a gas leak; call 9-1-1 from outside the house. Herb Kirchhoff has more than three decades of hands-on experience as an avid garden hobbyist and home handyman.

You might be interested:  How To Install A Baseboard Heater With Built In Thermostat?

What do you do when the pilot light goes out on your water heater?

What should you do when your water heater’s pilot light goes out?

  1. Turn the thermostat to the lowest setting.
  2. Turn the on/off/pilot switch to the “pilot” position.
  3. Remove the outer and inner panels to access your pilot light.

How do I know if pilot light is out?

How to Tell If the Pilot Light Is Out

  1. Locate the front cover panel on your furnace. It should be a little door that’s easily visible.
  2. If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame.
  3. If you don’t see a flame, your pilot light is out.
  4. If there is a flame, check the color.

How long do water heaters last?

How Long Do Water Heaters Last? Based on the manufacturer’s suggested service life, the life expectancy of a water heater is about eight to 12 years. That varies with the location and design of the unit, quality of installation, maintenance schedule and water quality.

How much does it cost to relight a pilot?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100. Have you ever relit your own pilot light?

Why is a pilot light called a pilot light?

Originally a pilot light was kept permanently alight, but this wastes gas. The term “pilot light” is also used occasionally for an electrical indicator light that illuminates to show that electrical power is available, or that an electrical device is operating.

You might be interested:  FAQ: What Is The Most Economical Electric Heater?

Should the pilot light always be on in a gas water heater?

The pilot should be on the water heating the house. The pilot flame can be difficult to see through a window. To know if the pilot is on or off, you need to remove the access door and shield and look at the burner and pilot through it.

What causes water heater pilot to go out?

A dirty thermocouple is the most common cause of malfunctioning water heater pilot light. Because the tip of the thermocouple is exposed to a direct flame, carbon can build up and cause the flame to malfunction or go out.

Will water heater leak gas if pilot goes out?

This is because modern gas-fueled water heaters feature valves that automatically close the supply of gas when the pilot light goes out. This is a very important safety feature, and if your water heater didn’t do this, then you would have a natural or propane gas leak on your hands, which is a serious explosion hazard.

Will gas leak if pilot light is off?

If the pilot light goes out on a storage or instantaneous hot water heater, space heater or a ducted heater, you will not have a gas leak. This is because all modern gas appliances with pilot lights have a fail-safe device that closes off the gas to the appliance in the case when the pilot may go out.

How much does it cost to replace a thermocouple on a water heater?

Thermocouple – $20 to $150 The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average.

You might be interested:  FAQ: How To Install Water Softener With Tankless Water Heater?

Can I manually light my gas water heater?

Lighting the Pilot Light on a Manual Hot Water Heater If your hot water heater is a manual, grab a long lighter. Turn the pilot dial to the off position and wait 5-10 minutes for any gas to dissipate. Then, turn the pilot dial until it says the word pilot. After that, set your temperate knob to low.

How do you know if you have a bad thermocouple?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

Leave a Reply

Your email address will not be published. Required fields are marked *