- 1 How do I light the pilot on my water heater?
- 2 How do you reset the pilot light on a water heater?
- 3 Why will my hot water heater not light?
- 4 Can you manually light a hot water heater?
- 5 Can I relight the pilot light by myself?
- 6 Can you manually light a water heater with electronic pilot?
- 7 How do I know if the pilot light is out on my water heater?
- 8 How long do water heaters last?
- 9 How do you know if you have a bad thermocouple?
- 10 What do you do if your pilot light won’t light?
- 11 Can a water heater explode?
- 12 How do you light a hot water heater without an igniter?
- 13 What do you do when you have no hot water?
How do I light the pilot on my water heater?
How to Light a Water Heater Pilot Light
- Open the door/cover over the pilot light access.
- Use a flashlight or a headlamp to find the burner inside.
- Turn the gas knob to “Pilot,” press and hold it down.
- While still holding the gas down, light that pilot.
How do you reset the pilot light on a water heater?
Once the pilot lights, keep holding the knob/button down for around one minute. After that time, slowly release the knob/button and check that there’s still a flame coming from the pilot. Go back to the gas valve and turn the knob to “On.” Usually you’ll hear a noise indicating the main burner is igniting.
Why will my hot water heater not light?
The water heater pilot light is a small flame that ignites the gas burner on your water heater. If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.
Can you manually light a hot water heater?
Lighting the Pilot Light on a Manual Hot Water Heater If your hot water heater is a manual, grab a long lighter. Turn the pilot dial to the off position and wait 5-10 minutes for any gas to dissipate. Then, turn the pilot dial until it says the word pilot. After that, set your temperate knob to low.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
Can you manually light a water heater with electronic pilot?
* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system. If the pilot light will not re-light, the problem could be a clogged pilot line or orifice, or gas is not reaching the water heater.
How do I know if the pilot light is out on my water heater?
It’s usually right on the panel. Turn and hold the knob to “Pilot” and push the ignitor. You should hear it click, and probably also a “whooshing” sound. Check in that gap, and you should see the light on.
How long do water heaters last?
How Long Do Water Heaters Last? Based on the manufacturer’s suggested service life, the life expectancy of a water heater is about eight to 12 years. That varies with the location and design of the unit, quality of installation, maintenance schedule and water quality.
How do you know if you have a bad thermocouple?
If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.
What do you do if your pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Can a water heater explode?
Water heater explosions are terrifying, and they can happen. Anything that causes excess pressure on your water heating system, such as a poor anode rod, or a lot of sediment buildup, can all cause your water heater to explode. A gas leak can also cause your water heater to explode because it is a tremendous fire risk.
How do you light a hot water heater without an igniter?
Lighting with No Igniter
- Take a long lighter to reach the pilot.
- Remove the plate attached below the dial box.
- Switch Pilot to OFF.
- Wait for a while, – 5-10 minutes until there won’t be any gas.
- Change the temperature to LOW, and switch to Pilot.
- Push ON/OFF dial down, and simultaneously use the lighter.
What do you do when you have no hot water?
Solved! What to Do When There’s No Hot Water
- Bump up the thermostat.
- Relight the pilot light.
- Fix a faulty thermocouple.
- Rekindle a blue flame.
- Inspect the gas line.
- Restart your water heater.
- Reset the circuit breaker.
- Call in the professionals.