Readers ask: How To Turn On Pilot Light Wall Heater?

How do you light a wall mounted gas heater?

Look for a button (usually red) next to the gas valve. If you see one, that’s a piezoelectric spark igniter. Push it in repeatedly until the pilot starts. If you don’t see a button, light the pilot by holding a lit match or a long-reach lighter next to the pilot orifice and keep it there until the pilot starts.

How do you turn a pilot light back on?

How to Relight a Pilot Light: 5 Steps

  1. Find the pilot light assembly and its reset switch. The furnace’s pilot light is usually positioned at the bottom of the unit by a knob.
  2. Set the reset switch to off. Turn the knob to the “Off” setting.
  3. Wait a moment.
  4. Relight the pilot light.
  5. Observe the furnace.

Why won’t my pilot light stay lit on my wall heater?

A pilot that won’t stay lit could be the result of a blockage in the pilot tube. Turn off the gas, clear the tube with compressed air, and relight the pilot. If that doesn’t work, you may need to call a repairman to come and install a new thermocouple.

You might be interested:  How To Install Laminate Flooring Around Water Heater?

Should the pilot light always be on in a gas furnace?

If you have an older gas furnace, your heating unit relies on a little blue flame known as a pilot light to ensure ignition of the burners. Since the pilot light needs to remain active, your furnace is always consuming some gas.

Where is the pilot light on a wall heater?

In some heaters, it is easy to locate the pilot light, as it is just behind the heater vent. For others, you will have to open the cover of the burner area or remove it altogether, then follow the gas connection from the main gas supply to the pilot light. The pilot light is inside the heater, behind a metal plate.

Does gas still flow when pilot light goes out?

If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.

How much does it cost to relight a pilot?

Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100. Have you ever relit your own pilot light?

What does the pilot light look like on an oven?

A pilot light is a small blue flame that ignites a gas appliance. Most modern gas appliances have electric starters or igniters. In some older natural gas appliances the pilot light can go out due to drafts, condensation or mechanical failures.

You might be interested:  How Does A Car Heater Work Diagram?

How safe is gas heaters?

Apart from carbon monoxide poisoning, there is also a potential fire risk of leaving a gas heater burning unattended. Under normal circumstances, gas heaters that meet all the gas safety standards don’t pose a fire risk.

What does pilot light look like?

Inspecting a Gas Furnace Pilot Light Flame A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip. The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip.

How do you reset a wall heater?

What I had to do is:

  1. Unscrew 3 mounting screws (1 on top and 2 on inside bottom by gas valve assemply) and pull cover/housing back.
  2. Turn on thermostat.
  3. Press/hold RED reset button (upper top left side of heater assembly; two wires were connected to it) for about 2 seconds. It immediately fired up.

What do I do if my pilot light won’t light?

How to Fix Your Pilot Light

  1. Find your gas valve.
  2. You need to turn the valve to the off position for at least three minutes.
  3. Once you have had the valve at off for a few minutes, switch it over to pilot setting.
  4. You will need a match that is lit.
  5. Set the pilot valve to the on position.

What are the symptoms of a bad thermocouple?

Failed Thermocouple Symptoms

  • Signs of contamination on the tube, e.g. discoloration, cracks, or pinholes.
  • Signs of wear or corrosion of the wirings, e.g. missing insulation or bare wire.
  • Physical damage to the connectors which can have an effect on the reliability of the test reading.

Leave a Reply

Your email address will not be published. Required fields are marked *